Assign appropriate IP Subnet to each network for the supernet 172

• Assign appropriate IP Subnet to each network for the supernet 172.16.0.0/16 and fill up following table
• Configure the following topology on packet tracer
• Allow console from PC10 to router R4.
• Assign appropriate IP Subnet to each network for the supernet 172.16.0.0/16 and fill up following table
• Configure the following topology on packet tracer
• Allow console from PC10 to router R4.

• Set banner on every device “UNAUTHORIZED LOGINS ARE PROHIBITED”
• Set credentials (username: cisco & password: cisco) on telnet and console.
• Configure all switches except LAN1 and LAN2 with Ports
• Set banner on every device “UNAUTHORIZED LOGINS ARE PROHIBITED”
• Set credentials (username: cisco & password: cisco) on telnet and console.
• Configure all switches except LAN1 and LAN2 with Ports

• fa1 – 2 for VLAN10
• fa3 - 4 for VLAN11
• fa1 – 2 for VLAN10
• fa3 - 4 for VLAN11

• fa5 - 6 for VLAN20
• fa7 - 8 for VLAN21
• fa 9 - 10 for VLAN30
• fa11 - 12 for VLAN31
• fa13 - 14 for VLAN40
• fa5 - 6 for VLAN20
• fa7 - 8 for VLAN21
• fa 9 - 10 for VLAN30
• fa11 - 12 for VLAN31
• fa13 - 14 for VLAN40

• fa15 - 16 for VLAN50
• fa15 - 16 for VLAN50

• Turn off CDP on R9 and R10
• Enable basic port security on all switch ports to prevent attacks.
• Configure root-bridge Make sure
• Turn off CDP on R9 and R10
• Enable basic port security on all switch ports to prevent attacks.
• Configure root-bridge Make sure

• S1 is root bridge for VLAN 11
• S1 is root bridge for VLAN 11

• S2 is root bridge for VLAN 21
• S3 is root bridge for VLAN31
• S2 is root bridge for VLAN 21
• S3 is root bridge for VLAN31

• Configure inter-vlan routing on R2 for VLAN 20,40,50.
• Configure RIP between R6 and R7 and make sure only vlan 10 and 11 are advertised over RIP.
• Configure EIGRP between R4 and R5 and make sure only vlan 30 and 31 are advertised over EIGRP.
• Configure inter-vlan routing on R2 for VLAN 20,40,50.
• Configure RIP between R6 and R7 and make sure only vlan 10 and 11 are advertised over RIP.
• Configure EIGRP between R4 and R5 and make sure only vlan 30 and 31 are advertised over EIGRP.

• Configure OSPF on R1,R2,R3 and R-Central and make sure only vlan 20 and 21 are advertised over OSPF. Avoid R-Central router links to be used for any type of traffic.
• Configure static routing between PC6 & PC7.
• Configure Ether channel between S1, S2 and S3 as mentioned in the diagram.
• Testing at the end of the topology
• Configure OSPF on R1,R2,R3 and R-Central and make sure only vlan 20 and 21 are advertised over OSPF. Avoid R-Central router links to be used for any type of traffic.
• Configure static routing between PC6 & PC7.
• Configure Ether channel between S1, S2 and S3 as mentioned in the diagram.
• Testing at the end of the topology

• vlan 10 and VLAN 11 should ping each other
• vlan 10 and VLAN 11 should ping each other

• vlan 20 and VLAN 21 should ping each other
• vlan 30 and VLAN 31 should ping each other
• vlan 20, 40 & 50 should ping each other.
• vlan 20 and VLAN 21 should ping each other
• vlan 30 and VLAN 31 should ping each other
• vlan 20, 40 & 50 should ping each other.

IP Addressing table

Objective:

IP Addressing table